An oxygen sensor in a vehicles engine is a part of the emission control system that feeds data to the engines computer. The combustion of the engine performs faster than it would in its absence. This gives the engine a better fuel efficiency meaning that it consumes only the amount needed reducing unnecessary wastage. Since it gives your engine better fuel efficiency, your engine dispels fewer fumes that pollute the environment. This is because it monitors the amount of fuel that enters the engine after monitoring the air to fuel ratio to determine if it is rich or lean. It is imperative therefore for O2 sensor recycling and listed below are ways of doing it.
Before you start the clean and recycle process, you should make sure that you have protective gears on your face and hands. A heat resistant glove for hands and a protective mask or goggles for the eyes will work. You can now take out the oxygene reader.
You can be able to peep in and see the dense carbon that has coated the reader. Next, put on the heat gloves and turn on a blowtorch to an optimum heat level. If you do not use the gloves you will only harm yourself.
Take a pair of tongs using your hand and hold the mouth of the oxygen reader on the flame produced by the blowtorch. You should then proceed to heat it up until it becomes fiery red hot. This makes sure that the carbon is broken down into bits and discarded, it is then ready to go.
Afterwards, you should turn off the flame so that the oxygen reader cools off. After a while, you can dip the tip of the reader in a bucket of cold water to make it cool further. You should not let it stay for long in water and make sure not to dip the whole reader in water.
When the oxygen reader has cooled off, you can shower the opening with compacted air so that you get rid of soot that would have formed inside it. After you have done this and still note that the soot has not completely come off, it is recommended that you go through the whole process again until it is rid of soot completely.
The only way for you to know whether you were successful is by putting the reader in your engine and testing it. The light usually comes on if you were not successful. This implies a new reader has to be purchased.
Using the blowtorch is not as easy as it looks. You have to be experienced in how to use it and at the right heat because any mishap will damage the sensor and even make you burn yourself. You can have an electric person do the cleanup process for you.
Another way of O2 sensor recycling is by taking it to a reprocessing center. This is advisable if you realize that the oxygen sensor cannot be reused after cleaning.
Before you start the clean and recycle process, you should make sure that you have protective gears on your face and hands. A heat resistant glove for hands and a protective mask or goggles for the eyes will work. You can now take out the oxygene reader.
You can be able to peep in and see the dense carbon that has coated the reader. Next, put on the heat gloves and turn on a blowtorch to an optimum heat level. If you do not use the gloves you will only harm yourself.
Take a pair of tongs using your hand and hold the mouth of the oxygen reader on the flame produced by the blowtorch. You should then proceed to heat it up until it becomes fiery red hot. This makes sure that the carbon is broken down into bits and discarded, it is then ready to go.
Afterwards, you should turn off the flame so that the oxygen reader cools off. After a while, you can dip the tip of the reader in a bucket of cold water to make it cool further. You should not let it stay for long in water and make sure not to dip the whole reader in water.
When the oxygen reader has cooled off, you can shower the opening with compacted air so that you get rid of soot that would have formed inside it. After you have done this and still note that the soot has not completely come off, it is recommended that you go through the whole process again until it is rid of soot completely.
The only way for you to know whether you were successful is by putting the reader in your engine and testing it. The light usually comes on if you were not successful. This implies a new reader has to be purchased.
Using the blowtorch is not as easy as it looks. You have to be experienced in how to use it and at the right heat because any mishap will damage the sensor and even make you burn yourself. You can have an electric person do the cleanup process for you.
Another way of O2 sensor recycling is by taking it to a reprocessing center. This is advisable if you realize that the oxygen sensor cannot be reused after cleaning.
About the Author:
Get in touch with the best services for o2 sensor recycling by touring our web pages at www.pgmrecoverysystems.com today. To know more about our scrap oxygen sensors, click the links at http://www.pgmrecoverysystems.com .
No comments:
Post a Comment